Key: Blow Molding Machine,Plastic Bottle Blowing Machine,Plastic Blowing Machine,Blow Moulding Machine

Blow Molding Machine Total:1 products
Blow Molding Machine CPX

YSXZB Series automatic rotary preformed cup filling and sealing machine is applicable to pack the products like yogurt ,milk,mineral water, beverage , ice cream, seasoning and so on.The process is from cup separating, sup falling,quantitive filling, suck cap film,sealing,and product conveying.The choice of the machine model and number of filling heads depends on the factors like required output, size and type of packaging and requirements for additional equipment.

The machine can provide a lot of solutions for the below field:suitable for both traditional and innovative packaging designs, quick change-over to alternative packaging, different ways of container closing.

Applicable Filling material:Liquid:yogurt ,milk,mineral water, beverage , ice cream, seasoning and so on Cap film material:Al+plastic laminated film;paper+plastic laminated film. Pre-cut lid or film roll. Preformed cup type: Paper cup,Plastic cup,Alu.cup etc.

Main Technical Data:

Function

name

Brand Brand country Function name Brand Brand country

Main

motor

SEW German Operation center

SIEM

ENS

German

High

pressure combination valve

Eugen Seitz Switzerland Low voltage electrical appliance

Schneider

/ SIEM

ENS

France /German

Stretch

cylinder

Rexroth German

Infrared heating

tube

PHILIPS Netherlands

Linear

Guides

Rexroth German Infrared thermometer OPTEX Japan

Gas

source

filter

FESTO German Encoder SICK German

Torque

clutch

MAYR German

Limit

switch

OMRON Japan

Low

pressure control solenoid

valve

MAC USA Photoelectric switch SICK German
Frequency converter Schneider France Proximity switch SICK German
PLC SIEMENS German Intermediate relay OMRON Japan

Program

mable Controllers

SIEMENS German      

 

 

Main parameter:

PRODUCTION DATA Mould
cavities
N 16
Max. body 
diameter
mm 75
Max. Height mm 260
M. diameter mm 38
Max. preform
Height
mm 140
Max. capacity ml 750
Nominal output
for 500ml,
bottle(*)
pcs/h 32000
DIMENSIO NS Host Length *Width)*
Height
mm 3800X2400X3200
Weight kg 21000
Heating furnace Length) *Width)*
Height
mm 5800X1400X2200
Weight kg 2500
ELECTRICAL
FEEDING
Voltage V 380
Frequency Hz 50
Total power
installed
kW 260
Main motor
power installed
kW < 5.5 <
Medium power
absorbed(**)
kW 80-100

COOLING
/HEATING SYSTEM
BASE MOULD Water inlet
10~20
Water inlet
pressure
bar 5
Flow m3/h 10
BODY MOULD Water inlet
temperature(**)
10~20
water inlet
pressure
bar 5
Flow m3/h 18
Heating furnace
But water
Cooling water temperature(**) pressure 10~20
Water inlet pressure bar 5
Flow m3/h 8
SERVICE AIR Nominal 
pressure
bar High pressure to low pressure
Air rate (**) m3/min
Filtering
grade (filter)
micron
Humidity
BLOW AIR Nominal
pressure
bar 40
Air rate (**) m3/min 20
Filtering 
grade(filter)
micron 0.01μ
Maximum
pressure
dew point
+3℃
Oil Maximum concentration 0.01 mg/ m3
HEATING Heating
groups * pcs
n 16*6
ENVIRONMENT Environment 
temperature (**)
(20℃-35℃)±3℃
Environment 
humidity (
without 
condensate)
% ≤70%
Max.
altitude
(over sea)
m
CONNECTIONS Connection
service air
Inch. 1
Connection
blow air
Inch. 2
Connection
water and oil
Inch. 2

 

Main technique:

1) Hopper and feeding mechanism: computer monitoring, no need for assistance; according to different types of preforms, the output speed can be adjusted arbitrarily

2) Heating furnace: When heating, the preform rotates while moving forward in the furnace to make the wall of the preform heat evenly; specially designed rapid hair cooling device; specially designed defective preform detection and ejection device

3) Blowing part: full monitoring by the host computer during the entire blowing production process

4) Special formwork system: The mold base is equipped with a pressure balance device to minimize the mold clamping line of the bottle during the molding of the bottle, ensuring the quality and performance of the bottle.

5) Stretching secondary blowing system: secondary blowing system, pre-blowing, high-pressure forming blowing, secondary blowing pressure, time adjustable .

6) Manipulator device: Made of stainless steel, precision machining; rotary manipulator with torsion overload protection to prevent equipment damage when equipment is not damaged

7) Safe and reliable mechanical transmission: using variable frequency motor, gearbox and inverter of SEW Company of Germanyod grade requirements.

8) Mold: audited by professional designers

Description: 1. Actual production depends on preform shape, preform wall thickness, bottle design and section quality
  2. Change according to different generation conditions, pressure and other factors
  3. The above water, electricity and gas parameters are calculated on the basis of 500ml water bottle.

 

Inquiry this product
Quick Links: Packing Machine  Case Erectors  Labeling Machine  Shrink Wrapper  Carton Sealer  Strapping Machine  Strapping Tool  Palletizer  Wrapping Machine  Carton Packer  Packing line  PP Straps  LLDPE Stretch Film Conveyor   Filling and Capping Machine   Vacuum Packaging Machine  Robot  Vertical Packaging Machine